Flexible Thin Film Research Articles

Transparent and flexible thermoelectric thin films based on copper sulfides

As a promising thermoelectric material, CuS has attracted significant attention due to its high conductivity, abundance of elements, and eco-friendliness. However, the study on CuS-based thermoelectric thin films is still lacking, impeding the advancement of CuS-based thermoelectric devices. Herein, high-quality CuS thin films have been fabricated through a facile vulcanization process. The effects of vulcanization temperature and film thickness on the thermoelectric properties of CuS thin films have been investigated. An optimal high power factor of 73.25 μW/m−1 K−2 is found at 400 K for a 20 nm-thick sample, and the optical transmittance is over 80% in the visible light spectrum. Meanwhile, excellent flexibility of the CuS thin films has been demonstrated. These results demonstrate the high promise of CuS thin films for transparent and flexible thermoelectric device applications.

Non-invasive FBG-based contact lens for continuous intraocular pressure monitoring

The intraocular pressure (IOP), or pressure inside the eye, is one of the key indicator for glaucoma diagnosis and treatment. The present work shows the design and fabrication of a non-invasive Fiber Bragg Grating (FBG) based contact lens for continuous IOP monitoring. By employing wet etching to reduce the FBG diameter, FBG based contact lens sensitivity and mechanical flexibility are enhanced. The contact lens is made of an optical fiber with a small core diameter that has an inscribed FBG of length 3 mm and is etched for a length of 40 mm to facilitate coiling the eFBG during fabrication. The soft contact lens was fabricated using flexible thin film technology with a transparent and flexible etched Fiber Bragg Grating (eFBG) integrated within flexible polydimethylsiloxane (PDMS) for sensing corneal deformations brought about by IOP variations. Experimental studies on the bionic eyeball model show that the Bragg wavelength shift is highly linear (r2 = 0.9694), with a very good sensitivity of 49.243 pm/mmHg in the IOP pressure range of 0 to 50 mmHg. Due to its ease of fabricating, simplicity of design, and ability to continuously measure pressure with good repeatability and stability, the proposed sensor thus offers a potential solution for IOP monitoring.

Texture and Se vacancy optimization induces high thermoelectric performance in Bi2Se3 flexible thin films

Texture and Se vacancy optimization induces high thermoelectric performance in Bi2Se3 flexible thin films

Ultrahigh thermoelectric properties of p‐type BixSb2−xTe3 thin films with exceptional flexibility for wearable energy harvesting

AbstractUse of a flexible thermoelectric source is a feasible approach to realizing self‐powered wearable electronics and the Internet of Things. Inorganic thin films are promising candidates for fabricating flexible power supply, but obtaining high‐thermoelectric‐performance thin films remains a big challenge. In the present work, a p‐type BixSb2−xTe3 thin film is designed with a high figure of merit of 1.11 at 393 K and exceptional flexibility (less than 5% increase in resistance after 1000 cycles of bending at a radius of ∼5 mm). The favorable comprehensive performance of the BixSb2−xTe3 flexible thin film is due to its excellent crystallinity, optimized carrier concentration, and low elastic modulus, which have been verified by experiments and theoretical calculations. Further, a flexible device is fabricated using the prepared p‐type BixSb2−xTe3 and n‐type Ag2Se thin films. Consequently, an outstanding power density of ∼1028 μW cm−2 is achieved at a temperature difference of 25 K. This work extends a novel concept to the fabrication of high‐performance flexible thin films and devices for wearable energy harvesting.

High stability visible-light photoresponse of flexible heterostructures based on LaCoO3 epitaxial films

The research of high-speed photodetector and high-speed optical receiver garners significant attention due to their indispensable properties in many fields including high-temperature event monitoring, security, and ad hoc network wireless communication. Inorganic perovskite oxides LaCoO3 films showcase an extensive prospect in this area owing to their remarkable photoconductive effect. Up to present, however, LaCoO3 films are mostly grown on rigid instead of flexible substrates, greatly limiting their applications to wearable optoelectronic sensors. In this work, we fabricated some flexible LaCoO3 thin films to study their photoresponse. By inserting SrTiO3 and BaTiO3 as buffer layers, we find that LaCoO3 thin films could epitaxially grow on the fluorphlogopite surface and show a stable photoresponse to visible-light. Nevertheless, we also found that the epitaxial strain and the content of surface-adsorbed oxygen could impact the photoconductivity. The mechanical strain generated by bending the fluorphlogopite substrate has been confirmed to has a tunable effect on the photoresponse. Moreover, with the fatigue tests of 105 bending cycles, the flexible LaCoO3 thin films maintain a good photoresponse without any essentially weakening, proving a superior mechanical durability and stability. This work not only indicates the feasibility of the LaCoO3 films applied for flexible photodetectors but also opens a path for other perovskite films applications for flexible substrate.

Investigation on preparation and performance of high-reliable ZnO–NiO@Cu NW flexible transparent conductive thin films

Investigation on preparation and performance of high-reliable ZnO–NiO@Cu NW flexible transparent conductive thin films

Dynamic optical information encoding strategy of flexible thin films based on Ba2SiO4 phosphor for ultra-long storage time

Nowadays, state-of-the-art for optical data storage (ODS) have emerged as a leader in the competition of data storage technologies. However, the development of optical storage technology based on optically stimulated luminescence (OSL) encounter the serious problems, of single storage mode and easily decoding. In this study, a series of Ba2SiO4 (denoted as BS): Eu2+, Ln3+ (Ln = Dy, Ho) phosphors with adjustable trap distributions (trap depths of 0.6–0.8 eV) have been developed by high-temperature solid-phase method and exhibit intense green emission peak located at 504 nm under excitation of 360 nm. Typically, BS: 0.02Eu2+, 0.02Ho3+ phosphor owns a shallow trap depth of 0.696 eV and BS: 0.02Eu2+, 0.02Dy3+ phosphor shows a deep trap depth of 0.81 eV. Interestingly, the flexible optical information storage film prepared by BS: 0.02Eu2+, 0.02Ho3+ phosphor through spin-coating technique can storage the “National Water Conservation Logo” pattern under NUV irradiation and reappear even after more than 60 days at 75 °C. Subsequently, multimodal anti-counterfeiting strategy is proposed by BS: Eu2+, Ln3+ (Ln = Dy, Ho) phosphors with adjustable trap depths and the flexible information coding device with high transmittance has been developed, in which encrypted message of “HELLO” and “86068” can be recognized at 75 °C and 130 °C, respectively. This work not only lays the foundation for realizing the durability of optical information storage, but also provides high security with multiple levels of retrievability.

Highly flexible poly-O-aminothiophenol/intercalated iodide composite with highly morphological properties for green hydrogen generation from Red Sea water

A highly flexible poly-O-amino thiophenol/intercalated iodide (POATP-I) nanocomposite has been successfully synthesized, in a one-step process, as a promising photocathode for H2 production through the Red Sea water. The fabrication of the photocathode involves the oxidation of O-amino thiophenol with iodine, leading to the formation of a remarkably flexible thin film of POATP-I. This thin film exhibits a well-developed network of polymer films. Notably, the nanocomposite demonstrates outstanding light absorbance properties in UV and Vis segments, boasting a calculated bandgap of 2.56 eV. To assess the efficiency of the photocathode, the current density (Jph) generated during the process is employed as a quantitative metric. The Jph values recorded in dark and light range from −0.2 to −1.7 mAcm−2, respectively. This substantial change in Jph highlights the impressive responsiveness of the POATP-I thin film to incident light, facilitating the high-energy electrons formation that contributes to the environmentally friendly hydrogen gas. Furthermore, the thin film exhibits notable responsiveness across various monochromatic photons, from 340 to 730 nm. Optimal performance is observed at 340 nm, where Jph reaches −0.45 mA.cm−2. Additionally, the estimated hydrogen production rate is calculated at 0.15 mmol h−1 for every 10 cm2 of the material’s surface. These remarkable characteristics position the material for potential industrial applications in hydrogen gas production, providing a sustainable and environmentally friendly solution for hydrogen production.

Automatic rehabilitation assessment method of upper limb motor function based on posture and distribution force.

The clinical rehabilitation assessment methods for hemiplegic upper limb motor function are often subjective, time-consuming, and non-uniform. This study proposes an automatic rehabilitation assessment method for upper limb motor function based on posture and distributed force measurements. Azure Kinect combined with MediaPipe was used to detect upper limb and hand movements, and the array distributed flexible thin film pressure sensor was employed to measure the distributed force of hand. This allowed for the automated measurement of 30 items within the Fugl-Meyer scale. Feature information was extracted separately from the affected and healthy sides, the feature ratios or deviation were then fed into a single/multiple fuzzy logic assessment model to determine the assessment score of each item. Finally, the total score of the hemiplegic upper limb motor function assessment was derived. Experiments were performed to evaluate the motor function of the subjects' upper extremities. Bland-Altman plots of physician and system scores showed good agreement. The results of the automated assessment system were highly correlated with the clinical Fugl-Meyer total score (r = 0.99, p < 0.001). The experimental results state that this system can automatically assess the motor function of the affected upper limb by measuring the posture and force distribution.

Synergistic Dual Doping of Sulfur and Copper for Improved Thermoelectric Properties of Silver Selenide Nanomaterials.

Research on flexible thermoelectric (TE) materials has typically focused on conducting polymers and conducting polymer-based composites. However, achieving TE properties comparable in magnitude to those exhibited by their inorganic counterparts remains a formidable challenge. This study focuses on the synthesis of silver selenide (Ag2 Se) nanomaterials using solvothermal methods and demonstrates a significant enhancement in their TE properties through the synergistic dual doping of sulfur and copper. Flexible TE thin films demonstrating excellent flexibility are successfully fabricated using vacuum filtration and hot-pressing techniques. The resulting thin films also exhibited outstanding TE performance, with a high Seebeck coefficient (S=-138.5µVK-1 ) and electrical conductivity (σ=1.19×105 Sm-1 ). The record power factor of 2296.8µWm-1 K-2 at room temperature is primarily attributed to enhanced carrier transport and interfacial energy filtration effects in the composite material. Capitalizing on these excellent TE properties, the maximum power output of flexible TE devices reached 1.13µW with a temperature difference of 28.6K. This study demonstrates the potential of Ag2 Se-based TE materials for flexible and efficient energy-harvesting applications.

Fabrication of low-cost flexible thermoelectric generator using conductive HB graphite paint operated by solar radiation

Paper-based flexible thin film thermoelectric generators have emerged as a promising and feasible alternative to organic and inorganic conductors due to their ability to operate at room temperature within a limited temperature range. Here, a flexible solar thermoelectric generator (STEG) designed from a single material has been introduced, prepared by a simple painting method. We prepared HB graphite-based conductive paint and demonstrated a very unique method to design flexible STEG devices. The graphite paint shows p-type semiconductive behaviour, while, in conjunction with the polyethyleneimine (PEI) polymer, it acts as an n-type material. Based on the transport properties, the paint appears to be a good candidate for designing STEG devices. At room temperature, the power factor of 378 nW m−1 K−2 for p-type paint and 1.51 nW m−1 K−2 for n-type paint is obtained. In order to examine flexibility over the long term, the performance of the material was inspected through 300 repeated cycles, and transport properties (conductivity) were found to increase from 21 700 S m−1 to 73 500 S m−1 due to the excellent emulsifying properties of gum Arabic, which were confirmed by field emission scanning electron microscope analysis. To evaluate the performance of the thermoelectric (TE) generator, eight pairs of p–n legs are fabricated on normal copier (80 GSM) paper, and an output voltage of ∼0.1 mV K−1 (∼5.5 mV) for a temperature gradient T of up to ∼60 K was achieved. Further, the performance of flexible TE devices can be improved by increasing the number of thermoelectric legs and by sandwiching the device between Kapton tapes. Our work suggests a promising and simple approach to achieving cost-effective conversion of solar energy into electricity and highlights the potential of flexible STEGs for low-power applications.

Control of Interfacial Defect States in the Flexible InGaZnO Thin Film Transistor with a 6FDA-MDA Gate Insulator by Using an Al2O3 Interlayer

Control of Interfacial Defect States in the Flexible InGaZnO Thin Film Transistor with a 6FDA-MDA Gate Insulator by Using an Al₂O₃ Interlayer

Tunable Dielectric Spectroscopy of PVDF Thin Films Crossbred with TiO2 Nanoparticles for the Storage Devices

AbstractPolyvinylidenefluoride (PVDF) is a semi‐crystalline ferroelectric polymer with a wide range of interesting properties and shows potentiality in a variety of technological applications. Flexible thin films of PVDF nanocomposites (NCs) have attracted many researchers due to their tunable electronic properties. This paper reports the synthesis, characterization, and dielectric studies of PVDF‐TiO2 NC thin films. The synthesized films are self‐supporting thin and the average thickness of the thin films is 60 µm measured using a Digital thickness gauge of resolution 0.01 mm. TiO2 nanoparticles are prepared using the combustion method. Commercially available PVDF granules are used to develop PVDF‐TiO2 NC thin films using the film casting technique. The structural study of the prepared thin films is carried out using XRD that confirms the retention of the β‐phase of PVDF. The functional group and bonding nature have been studied using FTIR Spectroscopy. The thermal stability of the NC thin films is studied using TGA. The variation of dielectric constant (DC), dielectric loss (DL), AC conductivity, and dissipation factor of the medium of pristine PVDF and PVDF‐TiO2 NC thin films are studied in the frequency range of 10 Hz to 8 MHz at ambient temperature. The dielectric constant of PVDF‐TiO2 NC thin films increases up to 8 wt% and anomaly for 10 wt% of TiO2 fillers in the PVDF matrix at a lower frequency and found to decrease with increasing frequency. The dielectric loss of NC thin films is high at a lower frequency and decreases with an increase in the frequency that is in good agreement with the Maxwell–Wagner type of interfacial polarization. At lower frequencies, the dielectric constant of PVDF‐TiO2 NC increases with the increase in filler content. AC conductivity shows a sharp increase at higher frequencies whereas the dissipation factor of the polymer NCs remains unaltered with respect to frequency by maintaining the trend. This suggests that PVDF‐TiO2 NC is potential material for energy storage devices.

Plasticizer–gelatin mixed solutions as skin protection materials with flexible-film-forming capability

To demonstrate the feasibility of plasticizer–gelatin solutions as novel skin protection materials from a physical aspect, we evaluated the rheological properties of the solutions and the mechanical properties and textures of their dried sheets and films. Three types of sugars and polyols were employed as organic plasticizers and mixed with gelatin in solutions at plasticizer/gelatin weight ratios of 0.13–1.67. The plasticizers minimally affected the viscosities and gelation temperatures of the gelatin solutions, but they remarkably softened dried gelatin sheets, except for propylene glycol. Glycerol exhibited the best plasticizing effects, but the sheets obtained using glycerol showed tacky textures. Preliminary investigations on the film-forming properties of the solutions on the human skin showed that the fructose–gelatin solution at a weight ratio of 1.0 formed a flexible thin film with a texture and mechanical properties similar to those of a commercially available polyurethane-based flexible film dressing. In terms of physical properties, we conclude that the fructose–gelatin solution has potential as a skin protection material that transforms from a solution to a film on the skin.

A flexible, thin-film microchannel electrode array device for selective subdiaphragmatic vagus nerve recording

The vagus nerve (VN) plays an important role in regulating physiological conditions in the gastrointestinal (GI) tract by communicating via the parasympathetic pathway to the enteric nervous system (ENS). However, the lack of knowledge in the neurophysiology of the VN and GI tract limits the development of advanced treatments for autonomic dysfunctions related to the VN. To better understand the complicated underlying mechanisms of the VN-GI tract neurophysiology, it is necessary to use an advanced device enabled by microfabrication technologies. Among several candidates including intraneural probe array and extraneural cuff electrodes, microchannel electrode array devices can be used to interface with smaller numbers of nerve fibers by securing them in the separate channel structures. Previous microchannel electrode array devices to interface teased nerve structures are relatively bulky with thickness around 200 µm. The thick design can potentially harm the delicate tissue structures, including the nerve itself. In this paper, we present a flexible thin film based microchannel electrode array device (thickness: 11.5 µm) that can interface with one of the subdiaphragmatic nerve branches of the VN in a rat. We demonstrated recording evoked compound action potentials (ECAP) from a transected nerve ending that has multiple nerve fibers. Moreover, our analysis confirmed that the signals are from C-fibers that are critical in regulating autonomic neurophysiology in the GI tract.

A facile in-situ reaction method for preparing flexible Sb2Te3 thermoelectric thin films

Inorganic p-type Sb2Te3 flexible thin films (f-TFs) with eco-friendly and high thermoelectric performance have attracted wide research interest and potential for commercial applications. This study employs a facile in-situ reaction method to prepare flexible Sb2Te3 thin films by rationally adjusting the synthesized temperature. The prepared thin films show good crystallinity, which enhances the electrical conductivity of ~1,440 S·cm-1 due to the weakened carrier scattering. Simultaneously, the optimized carrier concentration, through adjusting the synthesis temperature, causes the intermediate Seebeck coefficient. Consequently, a high-power factor (16.0 μW·cm-1·K-2 at 300 K) is achieved for Sb2Te3 f-TFs prepared at 623 K. Besides, the f-TFs also exhibit good flexibility due to the slight change in resistance after bending. This study specifies that the in-situ reaction method is an effective route to prepare Sb2Te3 f-TFs with high thermoelectric performance.

How to establish the relationship between wetting parameters and the mechanical properties of a flexible thin film

Conventional testing methods face limitations in identifying the mechanical properties of flexible film coatings. In this study, the mechanical properties of the polydimethylsiloxane (PDMS) flexible film coating were obtained by analyzing the dynamic wetting process of droplets on the surface. Results showed that the variation of contact angle can be divided into three regions during wetting, and the deformation height of the PDMS film increased rapidly and then decreased. Furthermore, a new model including interfacial tensions and the elastic force was proposed to establish the relationship among contact angle, deformation height and elastic modulus of the coating. The elastic modulus of the coating obtained from this model had an error of less than 10 % compared to the actual value.

Multifunctional Flexible Ferroelectric Thin Films with Large Electrocaloric Effect and High Energy Storage Performance.

Flexible ferroelectric films with high polarization hold great promise for energy storage and electrocaloric (EC) refrigeration. Herein, we fabricate a lead-free Mn-modified 0.75 Bi(Mg0.5Ti0.5)O3-0.25 BaTiO3 (BMT-BTO) thin film based on a flexible mica substrate. Excellent EC performance with maximum adiabatic temperature change (ΔT ∼23.5 K) and isothermal entropy change (ΔS ∼33.1 J K-1 kg-1) is achieved in the flexible BMT-BTO film, which is attributed to the local structural transition and lattice disorder near 90 °C. Meanwhile, a good energy storage density of ∼70.6 J cm-3 and a quite high efficiency of ∼82% are realized in the same ferroelectric film, accompanied by excellent stability of frequency and electric fatigue (500-10 kHz and 108 cycles). Furthermore, there is no apparent variation in performance under different bending strains. These prominent properties indicate that the multifunctional BMT-BTO ferroelectric film is a promising candidate for applications of flexible energy storage and EC refrigeration.

Electrode-free flexible batteries enabled by electro-deposition of both Zn and MnO2 from electrolytes

Flexible thin-film and cable batteries are fabricated with the pre-coating steps of anode and cathode materials replaced by one-step charging.

Solution slot-die coating perovskite film crystalline growth observed by &lt;i&gt;in situ&lt;/i&gt; GIWAXS/GISAXS

Solution method is an important means of fabricating optoelectronic devices. During the thin film sample preparation, organic or inorganic perovskite semiconductor material usually needs to be finished in a glove box. However, most of the traditional experimental characterizations under the air environment, it is hard to reflect the reality of the structure and performance between film and device, therefore it is urgently needed to solve the microstructure evolutions of these semiconductor films based on &lt;i&gt;in situ&lt;/i&gt; real-time representation technique. In this work, we report a synchrotron-based grazing incidence wide and small-angle scattering (GIWAXS and GISAXS) &lt;i&gt;in situ&lt;/i&gt; real-time observation technique combined with a mini glove box, thereby realizing the standard glove box environment (H&lt;sub&gt;2&lt;/sub&gt;O, O&lt;sub&gt;2&lt;/sub&gt; content all reached below 1×10&lt;sup&gt;–6&lt;/sup&gt;) under remote control film spin coating or slot-die preparation and various sample post-processing. Meanwhile, this technique can real-time monitor the microstructure and morphology evolution of semiconductor film during fabrication. Based on the &lt;i&gt;in situ&lt;/i&gt; device and GIWAXS, SnO&lt;sub&gt;2&lt;/sub&gt; ETL interface induced perovskite growth crystallization process shows that CQDs additive can result in three-dimensional perovskite, with the random orientation growth changing into highly ordered vertical orientation, meanwhile can effectively restrain the low-dimensional perovskite domain formation, helping to reveal the film microstructure transformation of inner driving force and providing the perovskite device preparation process optimized with experimental and theoretical basis. The conversion efficiency of large-area fully flexible three-dimensional perovskite thin film solar cells prepared by the roll-to-roll total solution slit coating method is increased to 5.23% (the area of a single device is ~15 cm&lt;sup&gt;2&lt;/sup&gt;). Therefore, using the &lt;i&gt;in situ&lt;/i&gt; synchrotron-based glove box device, the microstructure evolution and the associated device preparation conditions of perovskite and organic semiconductor thin films can be controlled, and the thin film growth interface characteristics and film quality can be further controlled, which is the key technology to control the optimization process conditions of semiconductor thin films and devices.